home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
QRZ! Ham Radio 3
/
QRZ Ham Radio Callsign Database - Volume 3.iso
/
digests
/
homebrew
/
930120.txt
< prev
next >
Wrap
Internet Message Format
|
1994-06-04
|
5KB
Date: Thu, 2 Dec 93 04:30:42 PST
From: Ham-Homebrew Mailing List and Newsgroup <ham-homebrew@ucsd.edu>
Errors-To: Ham-Homebrew-Errors@UCSD.Edu
Reply-To: Ham-Homebrew@UCSD.Edu
Precedence: Bulk
Subject: Ham-Homebrew Digest V93 #120
To: Ham-Homebrew
Ham-Homebrew Digest Thu, 2 Dec 93 Volume 93 : Issue 120
Today's Topics:
sw-radio coils...question.
Telephone Interface Circuit ?
TMS32010
Send Replies or notes for publication to: <Ham-Homebrew@UCSD.Edu>
Send subscription requests to: <Ham-Homebrew-REQUEST@UCSD.Edu>
Problems you can't solve otherwise to brian@ucsd.edu.
Archives of past issues of the Ham-Homebrew Digest are available
(by FTP only) from UCSD.Edu in directory "mailarchives/ham-homebrew".
We trust that readers are intelligent enough to realize that all text
herein consists of personal comments and does not represent the official
policies or positions of any party. Your mileage may vary. So there.
----------------------------------------------------------------------
Date: Tue, 30 Nov 1993 18:21:50 GMT
From: swrinde!sgiblab!sgigate.sgi.com!olivea!news.bu.edu!att!cbnewsm!jeffj@network.ucsd.edu
Subject: sw-radio coils...question.
To: ham-homebrew@ucsd.edu
In article <2649@arrl.org> zlau@arrl.org (Zack Lau) writes:
>In rec.radio.amateur.homebrew, st92ba44@dunx1.ocs.drexel.edu ( antonio gatta) writes:
>> I'm not sure if this is the right place to ask but the title seemed
>> appropriate (and I couldn't find a faq). Anyhows, I'm working on
>> a crystal shortwave radio which requires a t-50-2 toroid core onto
>> which the coil is wound. I'm wondering if a straight (bar) ferrite
>They are similar in that both are used to increase the inductance of a
>coil. However, type 2 iron powder of 10, while ferrite materials usually
>have a much higher permeability (though some VHF materials have a similar
>permeability). Ferrites typically have higher loss, though I've seen
>inductors wound on type 67 material with low loss. Many will have 1 to
>2 magnitudes more loss. Ferrites are often less frequency stable.
I was wondering about the differences between the various core types.
In some applications they call for T-50-2 and others they call for
T-50-6. A lot of times it looks like they are using what they have on
hand and you could subsitute a T-50-2 for a T-50-6 or vice versa.
Is the 2 or the 6 extender more of a indication of the amount of power
the toriods can handle? As I am just getting started in doing some
of my own homebrewing it would be nice to know that I can use a T-50-2
that I have on hand rather then having to wait for mailorder to show
up with a T-50-6. The applications I am working with are VFO's, output
filters and matching impedances. Could someone enlighten me on toriods?
73!
Jeff
--
Jeff Jones AB6MB | Vote out those who voted for the North American
jeffj@seeker.mystic.com | Free Trade Agreement!
Infolinc BBS 510-778-5929 |
------------------------------
Date: Wed, 1 Dec 1993 09:53:17 GMT
From: news.cerf.net!pagesat!netsys!agate!howland.reston.ans.net!ee.und.ac.za!hippo.ru.ac.za!pukrs7.puk.ac.za!pc2.puk.ac.za!itbkl@network.ucsd.edu
Subject: Telephone Interface Circuit ?
To: ham-homebrew@ucsd.edu
Hi.
I am looking for examples of circuits that will allow me to interface any
audio based equipment (say a PC's soundblaster card or audio from HF rig,
etc.) to the telephone line.
The circuit should have all the lightning protection, isolation, etc. that
is sufficient for the Telco to pass an acceptance test.
I have in mind a circuit with the following interfaces :
a) connection to telephone line.
b) audio out
c) audio in.
d) ring detect (say 5v out = ring)
e) go off-hook (say +5V means the circuit goes off-hook and puts the audio
through).
I am shure there must be some circuits available somewhere ? What do you
guys use for phone patching ? (Not legal over here).
Thanks.
Please send any replies via Email.
Keith
ZS6TW
------------------------------
Date: Tue, 30 Nov 1993 16:41:04 GMT
From: swrinde!sgiblab!news.kpc.com!kpc!nat@network.ucsd.edu
Subject: TMS32010
To: ham-homebrew@ucsd.edu
Hi,
Anyone know of a place where one could buy the TI TMS32010 DSP chip
in single quantities? Any idea how expensive this chip is? I know this
chip is at least 8 years old. My adviser in graduate school had a tms32010
system development kit from TI and I implemented many filters on it. While
we are on it does TI still sell the development kit for the tms32010 ? The
kit had a build in assembler and all you had to do was to download the
assembly code in ascii from a host machine. The development board intercepted
the incomming stream and assembled it on the fly. On the whole it was a neat
set up.
Thanks in advance.
Nat.
--
-------------------------------------------------------------------------
Natarajan Gurumoorthy AB6SJ Kubota Pacific Computer, Inc.
nat@kpc.com 2630 Walsh Avenue
Phone 408 987 3341 Santa Clara, California 95051.
------------------------------
End of Ham-Homebrew Digest V93 #120
******************************
******************************